Showing all 13 results
-
Pigtail Connector for IGN-1A and GM MAF Sensors
$15.994' Flying lead pigtail for IGN-1A coils. The extra length makes these easy to bundle up into a single ignition control harness without needing splices near the coil. Power and primary ground wires are 18 gauge to better handle these coils' power req...
Add to cart -
Crimp Connector for IGN-1A
$5.49Connector for IGN-1A coils, includes crimp on terminals/pins. Like all of our 'ready to crimp' connectors- we include an extra terminal/pin, just in case.
Read more -
Wire – Single Core Shielded 20 Gauge – 10′
$8.50Wire - Single Core Shielded 20 Gauge - Length = 10' Shielded single core 20 gauge wire helps cut out interference -- Perfect for Tach/Ignition Signal! This temperature resistant wire has one 20 gauge wires in the shield. Has many other uses where you n...
Add to cart -
Crimp Connector for IGN-1 or IGN-1CD
$6.99Metri-Pack crimp connector for wiring up IGN-1 or IGN-1CD coils. Like all of our 'ready to crimp' connectors- we include an extra terminal/pin, just in case you goof one up.
Add to cart -
Crimp Connector for IGN-4
$13.49Crimp connector and pins for IGN-4 coil. This is a standard "junior timer" sort of connector that has other uses such as Bosch crankshaft position sensors and throttle position sensors. Like all of our 'ready to crimp' connectors, we include an extra t...
Add to cart -
Crimp Connector for IGN-6
$5.49Included is a Weather Pack type connector for IGN-6 coils. The pins and seals are sized for 14 to 16 gauge wire. Like our other DIYAutoTune Weather Packs, we include an extra pin, just in case.
Add to cart -
5 Wire Pigtail for GM MAF Sensors
$13.49This 5 wire pigtail connector fits 5 wire type GM MAF sensors from 1985 to 1989, as well as IGN1A coils and some GM DIS modules. Replaces GM part number 12085497. Note that we only have a few of these left in stock, when they are gone we w...
Add to cart -
4 Wire Pigtail for Ford MAF/MAP/Coils
$12.994 wire pigtail connector that fits a variety of Ford applications. This connector has been used on Ford 4 wire MAF sensors, certain MAP sensors, and many 6 cylinder distributorless ignition coils including EDIS applications.
Add to cart -
2 Wire VSS/Ignition Connector
$15.00This 2 wire pigtail connector replaces GM part number 12101855. Used on a variety of applications, including some distribtutorless ignitions, vehicle speed sensors, and many chassis wiring locations. Please check mating connectors before ordering.
Add to cart -
5 Wire Pigtail for GM DIS Modules
$22.00This pigtail connector fits some GM OBD-I external DIS modules, including most 1995 and earlier Saturns. Check your module for the "missing pin" position to make sure this is the right one for your module. Replaces GM part number 12101880
Add to cart -
Black Pigtail for Ford TFI Ignitions
$15.00Black Ford TFI module connector. Note that this is not keyed the same way as the gray connector; the notch on the right side of this connector in the photo is on the left side of the gray connector. Check your module before ordering.
Add to cart -
Gray Pigtail for Ford TFI Ignitions
$15.00Gray connector fits certain Ford TFI systems. We've confirmed this was used on certain 5.0 Mustangs among other applications. It also appears to fit some neutral safety switches and distributorless ignitions. Note that the gray color is not purely a cosme...
Add to cart -
Ignition Coil Pigtail for Ford TFI
$11.00This pigtail has 10" leads and fits Ford TFI ignition coils. Used on 5.0 Mustangs, injected 351 Windsor motors, the 2.3 Turbo, various incarnations of the 3.8 V6, and many others. Just the thing if you're making a new wiring harness for your 5.0 or other ...
Add to cart